Dialogic Driver Download

The following screen shots indicate the typical installation and configuration sequence for the Dialogic System Release 5 software under Win 2000.

NOTE: These instructions are offered as a guide only. Please contact Dialogic for additional information and any changes. Please be aware that these instructions represent just one install method and may not be suitable for all machines and software configurations.

Download the Latest Service Update for Dialogic® HMP for Windows - Login Required. Dialogic® Brooktrout® TR1034 Fax Boards - more articles Software and drivers. If you are looking here for drivers for Dialogic ® Brooktrout ® Fax products, then perhaps you have purchased a Dialogic ® Brooktrout ® Fax Board or Dialogic ® Brooktrout ® SR140 Fax Software license without the fax application software you need to make it work? In this case, you do not need drivers - you.

********************************************************

Section 1: Install the hardware

********************************************************

Install ISA Dialogic Card

Dialogic ISA voice cards have jumper switches for setting the hardware interrupt level (IRQ) and base memory address segment. When fitting these Dialogic voice cards, it is essential to choose a hardware interrupt level and base memory address segment that do not conflict with existing equipment installed in your PC.

How to check for un-allocated IRQ and memory on Windows NT:

How to check for un-allocated IRQ and memory on Windows 2000/XP:

Having identified suitable free IRQ and memory address, configure the card by setting the jumpers and switches located on the card. IRQ 5 is usually a good choice, the base memory address can usually be left at the default D000.

1) After fitting the Dialogic ISA voice card, re-start the PC.
2) Start the Dialogic Configuration Manager: From the Start menu, select Programs, then Dialogic System Software, then Dialogic Configuration Manager.
3) Connect to the local computer.
4) Auto card detection will begin.
5) The ISA card will not be auto detected. Select Add-Device from the Action Menu.
6) Select the voice card model.
7) Give the voice card a name or number.
8 ) Setup the correct IRQ and memory values. (May need to double-click on the displayed voice card icon first)
9 ) Set the country parameter to the correct value.
10) Select Start-Service from the Service menu. The service will take up to 30 seconds to start.
11) From the Service menu, select Startup-Mode, then Automatic.

Install PCI Dialogic Card

Dialogic PCI voice cards have a small rotary switch (on the circuit card), which sets the board number. If this is the first Dialogic voice card in the PC, set the board number to 1. Plug the Dialogic voice card into any available PCI slot on the PC mother board.

1) After fitting the Dialogic PCI voice card, re-start the PC. The 'Found New Hardware Wizard' will be displayed. Press Next.
2) Select the 'Search for a suitable driver' option.
3) Select only the 'Specify a location' option.
4) Browse to the Dialogic installation directory's DRVR subdirectory, Press Next.
5) The correct Dialogic card name should be displayed. Press Finish.
6) Start the Dialogic Configuration Manager: From the Start menu, select Programs, then Dialogic System Software, then Dialogic Configuration Manager.
7) Connect to the local computer, auto card detection will begin.
8) Check if the voice card has been auto-detected.
9) Double click on the voice card icon and set the country parameter to the correct value.
10) Select Start-Service from the Service menu. The service will take up to 30 seconds to start.
11) From the Service menu, select Startup-Mode, then Automatic.

If the card is not detected, or the model is displayed as ????, do the following:

Reboot the PC
Enter the system BIOS
Disable 'Plug & Play' and/or disable ACPI
Repeat steps 7 to 9 above

********************************************************

Section 2: Install Dialogic Software

********************************************************

1) Run the Dialogic SR5 program and select the 'custom' installation option.

********************************************************

2) Make certain that the TAPI component of the Dialogic drivers is selected as part of the install.

3) Select 'GlobalCall' (This will set the software to use GlobalCall but does not install all of the GlobalCall software. You must remember to install GlobalCall separately below. )

4) For Analog cards for each of the next two dialog boxes, select no options
For digital cards (i.e. T1, E1) Consult the Dialogic documentation for the correct options for your installation. (Please use T1 robbed bit as it does not appear that PRI supports TAPI. If you will be using the SC Bus to connect multiple cards together then you will need to select the SCx option also.)

5)Complete the installation

6) Reboot

********************************************************

Section 3: Configuring the Dialogic Drivers

********************************************************

Start 'Dialogic Configuration Manager (DCM)' from the Start Menu. The first time you run DCM, you may see a 'computer name' dialog box. Select 'local' and hit the 'connect' button. Once DCM is up:

When using an ISA board (or board with jumpers):

1) Select the menu option 'Action | Add Device' 2) Select your Dialogic board
3) Set the Address and IRQ to match the setting on the hardware.
4) See 'Installing the Dialogic Hardware'
5) Select the menu option 'Service | Startup Mode | Automatic'
6) Close Dialogic Configuration Manager
7) Reboot the computer.

When using a PCI board (or board with NO jumpers):

The Dialogic board should automatically be detected and be on your screen
1) Select the menu option 'Service | Startup Mode | Automatic'
2) Close Dialogic Configuration Manager
3) Reboot the computer.

Note: After that, you can run one of the Dialogic Sample Programs such as 'Multi-Threaded Voice' or 'Synchronous Multi-threaded' to verify that the board is installed properly.

****************************************************************

Section 4: Installing Service Pack 1 (SP1)

****************************************************************

1) Check the link below for the latest service pack: http://resource.intel.com/telecom/support/releases/winnt/Sr511/index.htm.
2) Download the latest service pack.
3) Run setup to install.
4) Then reboot again.

****************************************************************

Section 5: Installing and Configure GlobalCall

(Only if using digital cards)

****************************************************************

Installing GlobalCall

NOTE: Checking GlobalCall in the main software setup above just selects the option to use GlobalCall. Both of these steps are important. You must install the GlobalCall software separately here.

1) Run Setup
2) Click on Custom
3) Select your location. In the US that would be North American protocols.
4) Also select online documentation
5) Select All protocols (US and Mexico)
6) Click OK on through
7) Restart again

Configure GlobalCall

1) Use Notepad to edit 'ProgramFilesDialogicCfgicapi.cfg'
2) Edit the line for parameter $14 to look like this:

3)Save and close

For Wink Start:

1) Use Notepad to edit 'Program FilesDialogicdataSPANDTI.PRM'

2) Save and close
3) Open the Dialogic Configuration Manager (DCM) and stop services if they are running
4) Select the board you wish to configure and repeat for all boards
5) Select the 'misc' panel
6) Click on ParametersFile
7) Under the value, enter 'spandti.prm'

****************************************************************

Section 6: Configuring the Dialogic TSP

****************************************************************

1. Run the Telephony applet in the Control Panel:

2. Click the Telephony Drivers tab. (Note: For Windows 2000/XP, select the Advanced tab.)

3. If the Dialogic Service Provider for NT does not appear in the Telephony Drivers tab, do the following to add it:

4. Click Detect Boards to update the list of Dialogic board channels (dxxxB1C1 is board 1 channel 1). The list is updated to match the configuration that was most recently started. You can click Help to access on-line help for the TSP configuration.

5. Click on the 'Advanced' button causing the 'Configuration Service' dialog box to appear. It allows setting of the the number of rings after which the call should be reported, definition of disconnect/busy tones which are used by your telephone network, and the commands used by the PBX to transfer calls correctly. For more information please see also: Call parameters configuration, Configuring Call Transfers and Conferencing and Disconnection Detection

6. Click OK to close the Dialogic TSP Configuration dialog.

After installation use the Dialogic Configuration Manager to configure and start the board.

****************************************************************

Section 7: Installing the Dialogic TAPI Wave Driver

****************************************************************

1) Go to the Start Menu->Settings->Control Panel->Add/Remove Hardware to start the Add/Remove Hardware Wizard
Click Next.
2 ) Select Add/Troubleshoot a Device and click Next.
Windows will attempt to find any new plug and play devices. It should find none. Select 'Add a new device' and click Next.
3) Select 'No, I want to select the hardware from a list' and click Next
4) Select 'Sound, video and game controllers' and click Next
5) Click 'Have Disk' and browse to the 'Program FilesDialogicLIB' directory.
6) 'Select the 'Oemsetupfile' and click open. Then click OK on the next screen.
7) Select the 'Dialogic WAVE driver 1.X' and click Next.
8) Click Next. You will receive a warning that a digital signature is not found. Click Yes to continue the installation.
If asked for path to 'dlgwave.dll' it should be found in Windows' 'System32' directory, else it is also available in the 'Program FilesDialogicLIB' directory.
9)Restart the computer for the changes to take affect
See here for step-by-step guide with screenshots.

Dialogic Driver Download Windows 7

Note: The default wave format in our demo samples is PCM, 16bits, 8kHz, Mono which may not work in some of the Dialogic cards. If so, please use the PCM, 8bits, 11Khz, Mono wave files that many Intel / Dialogic cards support natively. Download our wave file in this format at 11khz8bitsmono.

Dialogic D4pci Driver Download

The old cards such as ProLine/2V, D/41E, D/41ESC, D/21D, D/41D, D/21H, D/41H only support wave files in u-LAW, 8kHz, 8bit, Mono format, so please using these wave files in 'demowave_u-law' directory instead of the 'demowave_pcm'.